This is a list of all Error codes for the DynaTrol.
Note: Many of these error codes have an ‘Err’ prefix rather than an ‘E-‘ prefix on kilns made before Jan 2006.
Errors only detected when error codes setting is turned ON:
- E- A (E-A, EA, ErA, Er A, or Error A) - is the result of having too high a number programmed into one or more of the segments of the Vary-Fire program you are trying to fire.
- E- d (E-d, ErrD, ED, ErD) – One of the thermocouples' temperatures is 50°F above traveling set point. (Also see what it says under E- 9 below concerning proper setting of thermocouple circuits)
- E- 1 (E-1, Err1, E1, Er1) - Kiln temperature increasing slower than 12°F per hour when ramping for 22.5 min.
- E- 2 (E-2, Err2, E2, Er2) - Kiln temperature 50°F above hold temperature (18 seconds). If this a cooling segment, try using a cooling rate of 400°F or 500°F rather than one that is faster. Loose and overheated TC connections/ wires or old thermocouples can cause this too. Sometimes happens on an empty kiln during a first test firing.
- E- 3 (E-3, Err3, E3, Er3) - Kiln temperature 50°F below hold temperature (18 seconds). Pretty rare. Usually seen if heat treating metal and adding or removing parts at a higher temp (heat-treaters typically will turn the error codes off). Extremely uneven loading or something touching a thermocouple could cause it. Make sure your shelves are not blocking heat transfer between the zones (stagger shelves if you can). Usually E- 1 will appear first from a slow firing kiln as the kiln will slow itself and not move into the hold until all the thermocouples are reasonably close to the hold temp. Loose or overheated thermocouple connections/ wires or old thermocouples can cause this too. Can also be caused by programming a ramp rate that is too fast for the capacity of the kiln. Check to make sure relays are connected to the proper outputs. Check that thermocouples are connected to the proper inputs.
- E- 4 (E-4, Err4, E4, Er4) - Kiln temperature 50°F above previous hold when ramping down (18 seconds). Try using a cooling rate of 400°F or 500°F rather than one that is faster. Loose and overheated thermocouple connections/ wires or old thermocouples can cause this too.
- E- 5 (E-5, Err5, E5, Er5) - Kiln temperature 50°F below traveling set point when ramping down (18 seconds). Pretty rare. Loose or overheated thermocouple connections/ wires or old thermocouples may cause this.
- E- 6 (E-6, Err6, E6, Er6): reversed thermocouple leads or a negative (very cold) temp reading. If the all the thermocouples are hooked up right, AND you are still getting negative readings, AND the Board Temp is reading negative too, replace the board (From IDLE press OTHER again and again until it says “bdT”, press ENTER to see the board temp)
Error codes possible when error codes setting is turned OFF:
- E- 20 (E-20, E20, Er20): did not receive lock on Clock Generator Module- try again or replace board.
- E- 21 (E-21, E21, Er21): on-chip a2d (analog to digital) not responding/problem- try again or replace board.
- E- 22 (E-22, E22, Er22): off-chip a2d (analog to digital) not responding/problem- same as E- 6 on boards made after Jan 2006. With the display saying IDLE press 1,2,3 to see which thermocouple is reading oddly- really low or a negative number. Check thermocouple wires at their connection points to be sure that red is going to “-“ and yellow to “+”. If all seems well, the problem is probably that the thermocouple itself is flipped over/ reversed in the thermocouple connection block. Just pull the thermocouple out of the kiln wall and remove it from the thermocouple connection block, flip it over, reconnect it to the thermocouple connection block and re-install it in the kiln wall. See this link for thermocouple polarity.
- E- 23 (E-23, E23, Er23): SPI not responding/problem- try again or replace board.
- E- 24 (E-24, E24, Er24): EE access while in write cycle- try again or replace board.
- E- 25 (E-25, Er25, E25): a2d (analog to digital conversion) not responding during power up- try again or replace board.
- E- 26 (E-26, Er26, E26): a2d (analog to digital conversion) not working properly/problem- try again or replace the board.
- E- E (E-E, EE): EE miscommunication or failure- try again or replace board
- E-bd (Erbd): Bad board temperature. It usually will read very high- like 300°F at room temp (From IDLE press OTHER again and again until it says “bdT”, press ENTER to see the board temp). This may mean that there is too much heat in your kiln room on near the kiln. Try cooling off the panel with a small fan or getting more ventilation in the room. Try firing again. Sometimes this is an indication of a bad board that needs to be replaced (especially if it is obvious that the board temperature is not that hot.) Note that there is an "alarm" setting for this (factory set for 250°F). This can be changed as one of the settings in the "hidden menu".
- E- /: division by zero detected- try again or replace board.
- E- - (Err-): power loss during EE write- try again or replace board.
- E- R (E-R, ErrR, ER): ram and EE do not match- try again or replace board.
- E- A (E-A, ErrA, EA): invalid program variable- try again or replace board.
- E- 0 (E-0, Err0, E0): software error- try again or replace board.
- E- 8 (E-8, Err8, E8): if cone fire temperature decreasing in last segment- a relay or an element has just failed. Loose or overheated power wires or connections and/or thermocouple connections or wires or old thermocouples can cause this too. Basically something has happened that stopped the power getting to one or more of the sections at the end of the firing.
- E- 9 (E-9, Err9, E9): wrong thermocouple hardware/software setting- rarely the board, only on ones made after Jan- ’06. Means the thermocouple circuit type (S or K), the S or K jumper setting on the back of the board, and/or the internal menu S or K setting do not all match. Start with the thermocouple circuit; wires and thermocouples must match, so determine whether are they S or K. Then check the S or K jumper setting on the back of the board. (Located approx center of the board under the marking “R97”. The tiny black plastic coated jumper only touching one of the prongs it is set to K. If it's touching both prongs it is set to S). Be sure the jumper setting matches the type of thermocouples they have. Then check the setting in the menu (from IDLE press OTHER/ 4/ 4/ 3/ then OTHER again and again until it reads TYPE. Press ENTER and any number key will toggle it from K to S to K, set it to the Type of thermocouple they have and press ENTER. Try running it again- still E- 9, replace the board (this is rare to have to do). See this link for a photo and more.
- E- U (E-U): invalid user number - try again or replace board
- FAIL alternating with TC1, TC2 or TC3: Generally this is a failed thermocouple. The TC+ a number indicates which position (TC1=top, TC2=middle and TC3= bottom zone).
- (Pre-Jan ’06 boards often read this when they are turned on, press ENTER to get them to IDLE.)
- If the code is a solid E- P, ErrP, or PF it means a longer power outage, that the program is off and kiln is cooling- restarting is usually OK except in complex multiple ramp programs.
- If it is a flashing E- P, ErrP, or PF it means the program is still running and that the power was just off for a few seconds. If the power interruption is brief, the kiln will continue to fire when power is restored; in this case, there will be no indication of a power failure.
- Press ENTER to clear the error code.
- PF, E- P (E-P), ErrP: error in the power supply.
- tC-- : The red and yellow thermocouple extension wires are reversed.
- L7KH (or something that looks like that): This is not an error code. It is the software version in the control. It will flash briefly on the screen when you first turn the control on.
- STUC (stuck) indicates a key is not releasing. The outputs are turned off and stop the firing if in progress. It can be caused by moisture or stretched plastic from age or possible air bubble under the overlay. Sometimes heating gently with a hair dryer will remove the problem temporarily.
- ROR - Not an error code. This just stands for Rate of Rise. You might see this in conjunction with a E-1 error code.